 |
|
| These tongs are designed to give
you a maximum reach of 3.15 inches of insertion depth. That
gives you more reach for work on such large applications as façade
panels. |
back to top
| These tongs are designed
for box joints and turning corners in. They have a depth
of 1.57 inches that allow you to grab the work piece and easily
manipulate it. The materials are premium grade steel hardened
for long life with vinyl handles for sure grip. |
back to top
|
These are the standard
tongs used in most sheet metal applications. If
you are tired of having to buy cheap tongs over and over, then
these tongs are for you.
|
back to top
|
These tongs are designed for box joints and turning corners in. They
have a depth of 1.57 inches that allow you to grab the work piece
and easily manipulate it. The materials are premium grade
steel hardened for long life with vinyl handles for sure grip. |
back to top
| This European made
hand seamer is the best in the market place for closing 1 inch
and 1.5 inch mechanical seam panels. |
back to top
| The Double Lock Hand
seamer is used to close the second half of a 180 degree locking
seam. The double lock seam is the best most durable water
tight seam in the world. |
back to top
| Standing Single Lock Seamer |
| Designed for use
with 1 and 1 1/2 inch mechanical lock standing seam panels, this
tool offers all the benefits of the regular seaming tools without
the wear and tear on your back. This tool can be used to
create a 90 degree lock. This is perfect for setting a panel
in place before electric seaming. |
back to top
| Standing Double Lock Seamer |
| Designed for use with 1 and 1 1/2
inch mechanical lock standing seam panels, this tool offers all the
benefits of the regular seaming tools without the wear and tear on
your back. This tool can be used to create the second stage
of a 180 degree lock seam. |
back to top
| This tool creates the first stage
bend of the eaves edge. It bends the end of a pre-snipped panel
under so that it can be locked shut. Used in concert with the Eaves
Edge Seamer you get a clean professional water tight seal. |
back to top
|
This tool creates
the second, closing stage bend of the eaves edge. It clamps
on and closes the pre-bent eaves. |
back to top
| Every
tool box should have one of these. Our seam opening pliers
are the best in the business. Casted from the finest quality Austrian
steel these hand tools are used to open up seams that have been
either snapped in place or mechanically locked together. |
back to top
| These are perhaps the
most indispensable tool for anyone in the sheet metal business. Best
used for making long straight cuts these snips are hardened for long
life and are a must have for the sheet metal professional. |
back to top
| This
hammer is perfect for most seaming applications where an anvil
will be used. It’s made out of polyethylene with rounded
edges. This material is just hard enough to stand up to steel
but soft enough not to damage paint. |
back to top
| Angle Head Seaming Hammer |
| This hammer is designed
with its angled head to get into tighter places than you can normally
reach. Its perfect for corner and bread pan work. |
back to top
| This anvil is designed
to be used with either 1 inch or 1 1/2 inch mechanical lock seam. It
is perfect for creating the leading edge seam for panels that are
going to be electrically seamed together. |
back to top
| This
anvil is forged to a Rockwell hardness of 65, you won’t find
any harder seaming anvil on the market. It is designed for
more intricate work such as corners and special closures. |
back to top
| Compound Action Right Hand
Snips |
| These
snips are designed to be the snips you reach for every time. They
are stronger and made out of better steel than the snips from competitors
and therefore should last much longer. The strong spring
action insures that you won’t be wrestling with the snips,
instead you’ll be cutting material with minimal exertion. |
back to top
| Compound Action Left Snips |
| These
left hand versions of the snips to the left are designed for times
when you need to cut in the opposite direction to make a straight
line or to cut circles
Engage PIC 25.38 Seamer. |
back to top
| The Engage PIC 25.38
Seamer is designed to single lock or double lock 1 and 1.5 inch mechanical
lock seams in one pass, but the machine does more than that. It
can also bend in half and seam curved mechanical lock panels. |
back to top
|
This seamer is field tested throughout the US for durability. It is used to lock
the initial seam together on a mechanical lock 1 and 1.5 inch panel. |
back to top
| This
seamer works in concert with the 90 degree locking tool to close
the 180 degree lock on mechanical lock standing seam panels. |
back to top
| This tool creates the
first stage bend of the eaves edge. It bends the end of a pre-snipped
panel under so that it can be locked shut. Used in concert with the
Eaves Edge Seamer you get a clean professional water tight seal. |
back to top
| This
tool creates the second, closing stage bend of the eaves edge. It
clamps on and closed the pre-bent eaves edge. |
back to top |
|
